2015 Tacoma with Evo One and RF642W start 2 seconds then stop and re-try again

Question

Hi I need some helps please

I used guide# 19621 to install my Evo One into 2015 Tacom V6 and Auto-tran (with G-Key) using Toy2-Harness everything went fine, program Evo One and RF642W remote was fine. But the Truck only start and run about 2 seconds then it shut off and parking lights blink few times then it re-try to start second time cranking but engine won't start. I notice Immobilizer light was blinking the holl time during remote start, run and shut off, it seem IMO by pass is not working?

I re-check my connector twice from 20-pin connector and red-connector to ECM Blue/white and Lt. Green/black

Do I have to connect CAN wires (Gray and Gray/black) to OBDII connector? it did not mention in the guide at all.

I did connected Lock/Arm (Purle wire to vehicle Purple wire and Purple/white Unlock/Disarm to vehicle Green/black) work just fine. do I have to change any settings at all to get it going? I did update firmware to the lastest one on both Evo one and Remote start.

Here is what I have set FORTIN EVO ONE (2015 Toyota Tacoma V6, Auto-Tran)
Bypass firmware 79.34 - below is things that are ON

A1- Door locks
A3- Key Bypass
A7- Foot-Brake (output status)

B1- Unlock Driver Door Only
C1- OEM Remote Monitoring

Remote-starter firmware 1.16 Set as the following:
2.4 Configure main harness outputs as: White: (+) Start, Orange: (+) Ignition2, Pink: (+) Ignition, Yellow: (+) Start2.
3. Tachless sensitivity: 1
4.1 Remote car starter runtime: Gas: 15 minutes
6.2 Door Lock before and after remote-start: Unlock before remote start and lock after remote start
7.1 Safety locks: NONE
8.2 Unlock pulse time: Double 0.25 sec pulse
9.1 Active or Passive Starter Kill: Active. Press LOCK to activate the Alarm and starter-kill.
11.1 Confirmation: Silent on 1^st LOCK/UNLOCK press. Sound on 2^nd LOCK/UNLOCK press. Antenna LED active.
12.1 Sound Confirmation: Horn only. Output programmed to be used for vehicle horn
13.2 Pulse Confirmation: Short
14.1 Alarm and Starter Options: Alarm Disabled, remote starter enabled.
15.1 Smart door lock: Disabled
16.5 Cold start timer: Cold time OFF
18.1 Diesel mode: Disable
19.1 Turbo mode: Disable
20.2 Engine Supervision: Tachless only.
21.1 Start attempts:  2 times
24.4 Special Applications: Application 3. Turn OFF the engine when the foot-brake is pressed.
25 OFF
26.1 Hybrid Mode: Gas/diesel vehicle
29.1 Alarm duration: 30 seconds.
30.1 Valet Code: Ignition ON + 3x valet button
31.1 Special application programmable output: Disable
32.1 Ground out: Shut down 1s after remote start run time. Dark Blue wire (ground out)
33.1 Manual transmission ready mode activation: Activated by remote starter remote. Ready mode activated with the starters remote
34.1 Trunk output: Pulse 0.5 seconds
35.1 Door lock special application: Disable
36.3 Activation/Deactivation remote Valet mode: By valet button only
37.1 Security remote car starter special application: Disable
38.2 System control by OEM remote: Enable (press 3x lock to remote start (bypass module required)
39.1 Temperature control: Disable

Robert Saing

Answer 1

Did it program correctly and flash 10x times red as per step 6 in the guide? If so, it may just be that the light blue wire from the evo is on the wrong side of the vehicle IMI wire that is cut.

 

There are no can-bus connections on this vehicle.

Comments

Thank you for your help

I cannot count because Red led blink very fast, after I start the Truck then it turn itselft off which is it suppost to be doing then I shut off the Ignition key.

Here how I connected my IMI and IMO wires:

Light Blue/black from (20-PIN) to Light Green/black at ECM tap no cut.

Light Blue from (20-PIN) combined with White/red from (Red Conn) to ECM-Blue/white (cut)-Connector side.

White/green from (Red Conn) to ECM-Blue/white (cut)-Harness side

---

Put back the default 4.18 firmware in the bypass settings.

When programming the module, pay close attention to the first steps of programming. You to hold the programming button while inserting all the connectors. The order in which the connectors are connected actually matter on these generation toyota.

At step 6 when we state to start the vehicle, the vehicle is supposed to stay running and not shut down as you mentionned. If it does shut down, please check the actual connection and remove any T-taps if using t-taps.

---

I am put Bypass firmware back to 4.18 now I will try press and hold program button while connecting all connector then plug main 6 pin last, release program button when Led is RED

Then I will start the Truck, Instruction or guide said RED light flah 10 times then I can shut off and I already did that, will let you know after down grade Bypass firmware to 4.18 Thank you

--------------------------------------------------------------------------------------------------------------------------

​Hi Robert T

​Thank you for your help my Evo One is workig now after down grade Bypass firmware to 4.18 as you tell me to do,  you are the best thank you so much. I am very happy now